For several years we have tweaked our process to obtain as close to perfection as humanly possible.
#WIC 1T SMART SERIAL SERIAL#
1 x Cisco WIC-1T 1 Port Serial WAN Interface Card. When the port is in data communications equipment (DCE) mode, it indicates that Data Terminal Ready (DTR) and Request To Send (RTS) have been detected. TheCisco WIC-1T 1 Port Serial WAN Interface Card is capable to supports a single serial connection at up to T1/E1 rates. 2-port serial WIC and the 2-port A/S WIC have Cisco smart serial ports. When the port is in data terminal equipment (DTE) mode, the CONN LED indicates that Data Set Ready (DSR), Data Carrier Detect (DCD), and Clear To Send (CTS) have been detected. Figure Port Serial WIC Front Panel (WIC-1T) Serial port LED SERIAL Figure Port. Uses the same cabling as Cisco 2500 and Cisco 7000 serial ports.ĭoes not support hot swap, however no hardware damage will occur if it is swapped while the power is on.Įach serial card has one LED, labeled CONN for each port, which lights when the serial port is connected. The 1-port serial WAN interface card (WIC-1T) provides serial connections to remote sites or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, alarm systems, and packet over SONET (POS) devices. This connector is DB-60 on one end and can be V.35, RS-232, RS-449, X.21 or EIE-530 on the other end depending on your needs Uses the Cisco 60-pin "5-in-1" connector.
![wic 1t smart serial wic 1t smart serial](https://stinriverstorageprod.blob.core.windows.net/images/Cisco/WIC-2A/S/499234.jpg)
This interface card inserts into a Cisco mixed-media network module or directly into a Cisco WAN Interface Card (WIC) expansion slot.The Cisco WIC-1T Single Port Serial WAN Interface Card has 1-port serial port and provides serial connections to remote sites or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, alarm systems, and packet over SONET (POS) devices. The dB-60 connector supports any of five interface types (RS-232, RS-449, RS-530, V. I don't know what the T stands for, so your guess is as good as any that I have seen. Fast and easy cable marking: with WIC pre-printed cable markers. Basically, the 2T supports two ports and uses smaller connectors for one card. To see how easy it really is, watch this video. The 1-port serial WAN interface card supports a single serial connection at up to T1/E1 rates. The older WIC-1T has a single DB60 connector and newer WIC-2T has two Smart Serial connectors. 10X Smart Serial DTE DCE Back to Back Cable HWIC-1T pls sms me if keen - 83725802. Half or full-duplex data-transfer support 8x WIC-2T 2-Port Serial WAN Interface Card. Summary: Cisco WIC-1ENET= One-port Ethernet WAN interface cardġ0BaseT Ethernet interface with one RJ-45 port
![wic 1t smart serial wic 1t smart serial](https://ae01.alicdn.com/kf/HTB1XqCzPXXXXXcYXXXXq6xXFXXX5/-.jpg)
This WAN interface card supports asynchronous and synchronous traffic, and plugs directly into a WAN Interface Card (WIC) expansion slot. This 2-port serial WAN Interface Card supports two serial connections at up to T1/E1 rates. Summary: Cisco WIC-2T wan interface cards
![wic 1t smart serial wic 1t smart serial](https://c1.neweggimages.com/ProductImageCompressAll300/A8JA_1_20150712473095088.jpg)
![wic 1t smart serial wic 1t smart serial](https://www.itinstock.com/ekmps/shops/itinstock/images/cisco-1841-integrated-services-t1-e1-router-wic-1t-serial-wan-interface-card-51770-p.jpg)
35, RS-449Ĭompliant Standards: CE, UL 1950, FCC Part 15 B DB15F X21 to DB60 CISCO Cable: CAB-X21FC. Summary: 1-Port Serial WAN Interface Card The cables you listed use the smart serial connector so they will not work.